Skip to main content

The final steps

The final step is building the Button Board and the connecting everything together.
The Button Board.
For this you will need the following.
Veroboard I use (10 x 20 holes with the copper strips running horizontally)
5 x Buttons.
6 x Right Angle Male Pins.
Jumper wire.










Top view of the Button Board.

Flip the board over and cut the copper strips where indicated.










Bottom view of the Button Board.


That is most of the construction done. The only things left to do is cut off one end off two dupont wires (for ease make sure one is black) and solder the wires on to the connectors of the 2.5mm port.



ASSEMBLY

This is where it gets complicated. First we will connect the LCD screen to the Nano board.


Use 4 dupont wires and connect to the pins on the back of the LCD screen. The wire on the pin marked VCC goes to a 5v pin. GND to a Ground pin. SDA goes to pin A4 and SCL to A5.

Now the SD Card Slot.










CS to D10
SCK to D13
MOSI to D11
MISO to D12
VCC to 5v
GND to Ground

 Your SD card reader may have it's pins named differently but the pin order is usually the same.


Now to connect the Button Board.
 







I've numbered on the picture where each cable should go on the Nano board. The pin numbered D6 actually goes to D7

The Filter Board and the Amp.
















VCC to 5v Pin on the Nano Board
In to Amp in on the Filter Board
Both GND pins to the Ground Pins on the Nano Board.

On my Amp the is a green socket for two wires that go to the 3.5mm Socket I used a red wire for the in and Black for the GND and soldered the other ends to the 3.5mm socket.

The final piece of teh puzzle is the 2.5mm Motor Control socket. One wire goes to D6 and the other goes to the hopefully final Ground Pin.

The final piece of the puzzle is to programme the Arduino.

You should find the relevant .rar file here.
http://s000.tinyupload.com/index.php?file_id=97271397603044485767

Comments

  1. Hola duncan como hago para armar el casduino no entiendo ingles no entiendo como armarlo

    ReplyDelete

  2. Desafortunadamente mi español no es muy bueno. Voy a tratar de conseguir uno de mis amigos españoles para ayudarle.

    ReplyDelete
  3. Saludos Luis portillo,soy Alfredo Retrocant. Me ha pedido Duncan Edwards que sea portavoz en las consultas y dudas que tengas en el proyecto Casduino. Los autores del proyecto no dominan bien el Español. Ya te envié por mail todo lo necesario para construirte tu propio casduino. Si necesitas mas soporte o ayuda técnica estaremos encantado de ayudarte.

    Recibe un cordial saludo.

    ReplyDelete

Post a Comment

Popular posts from this blog

Introducing the TZXDuino

A Giant Leap For Nerd Kind.
I'm not usually one for silliness but Andrew Beer has been working hard in the background trying to programme the Arduino to play ZX Spectrum .TZX files without the need to convert to a .WAV. Today he has managed to do that with some .TZX files but also with .TAP files as well. The code is still very much in the early stages so the compatibility with.TZX files is still relatively low but in theory all .TAP files should work. I only have 5,246 to test.
What's even better is that the code will work on both the Arduitape and the CASDuino hardware by just uploading the programme to the Nano.

Simply download this file, unzip and load in the Arduino IDE.

TZXDuino 1.7

TZXDuino 1.7
This fixes issues with pause lengths that we never noticed before. It should fix games like Top Gun and Street Hawk for the Spectrum and make CDT files behave as they should for the Amstrad CPC.Changes.
*Maximum pause length of 8.3 seconds due to the TimerOne library has been worked around.
*ID20 Pause Block fixed.
*Temporary fix for pause after motor control removed.https://mega.nz/#!aEt1VJKZ!ZFw-fP3bkNTtiPlbG_IllmR94Xni3KvIGUn6Jggfof8

How to change Firmware on the Arduitape/TZXDuino/CASDuino.